The AN-16/i-M is a 3U-high rack-mounted mic- and line-level input device with sixteen high-quality microphone preamps and 24-bit A-to-D converters. Each channel contains a three-segment level meter, a continuously variable gain knob, a phase reverse switch, 48-volt phantom power, and a rumble filter with an 85Hz rolloff. In addition, each pair of channels can be Stereo Linked for stereo operation in a Pro16 Monitor Mixing System.

The rear panel of the AN-16/i-M contains a host of professional connectivity features. Each channel has a combo jack that can accept either XLR mic or 1/4-inch line-level (balanced or unbalanced) inputs. Sixteen passive mic Thru connectors create a built-in microphone splitter. Balanced insert points with separate 1/4-inch Send and Return jacks allow easy interfacing with external processing devices. The sixteen insert Sends can also be used as a set of post-gain direct audio outputs. The AN-16/i-M uses an internal power supply with a standard IEC power connector.

Two parallel A-Net outputs allow the AN-16/i-M to send A-Net data to multiple destinations, allowing for simultaneous patching to a monitor console and a front-of-house console. Both A-Net outputs feature heavy duty Neutrik EtherCon combo RJ45 connectors. The built-in A-Net Expansion jack allows two 16-channel A-Net streams to be combined onto a single cable (32x0 or 16x16), and the AN-16SBR System Bridge can be used to combine up to four 16-channel streams onto a single cable in a variety of bi-directional configurations.

As with all Pro16 Series products, Cat-5e cable runs of up to 500 feet (150 meters) are possible between devices.

Aviom AN-16/i-M

• Sixteen high quality mic preamplifiers, with 24-bit A-to-D converters
• XLR mic or 1/4-inch TRS balanced line-level inputs on combo jacks
• 48-volt phantom power on each channel
• Three-segment LED level meter
• Continuously variable gain knob for each channel
• Phase reverse switch per channel
• Rumble filter switch (85Hz rolloff) on each channel
• Stereo Link switch per pair of channels
• Built-in passive mic splitter
• Balanced insert send and return jacks (1/4-inch TRS)
• Dual A-Net outputs
• A-Net Expansion jack for 32x0 and 16x16 channel systems
• Internal universal power supply; IEC power connector

• Audio Inputs: 16, balanced mic- or lline-level, XLR combo connector
• XLR Input (mic/line) Pin 1: Ground; Pin 2: Audio +; Pin 3: Audio -
• TRS Line Inputs, & Send/Return Tip; Audio +; Ring: Audio -; Sleeve: Ground
• Audio Thru XLR; Pin 1: Ground; Pin 2: Audio +; Pin 3: Audio - Direct coupled passive throughput
• Insert Send Impedance balanced; Nominal level: 0dBu; Peak Level (A/D clip point): +14dBu
• The Insert Send connector is a line output in the signal path post gain, post filter, and post phase controls.
• Insert Return TRS balanced; Nominal level: 0dBu; Peak Level (A/D clip point): +14dBu
• The Insert Return connector is a line input to the signal path that is pre A/D conversion.
• Analog to Digital Conversion 48kHz sample rate, 24 bit
• Operating Level +4dBu
• Frequency Response 4Hz-22kHz
• A-Net Output one Category 5 (RJ45 connector)
• A-Net Expansion one Category 5 (RJ45 connector)
• Gain Range Mic: +6dB to +60dB; Line: -15dB to +36dB
• Channel LED Indicators Signal Present and Clip, per channel
• Line Inputs Impedance: 48k ohms
• Metering LEDs; green: Signal Present, red: Clip; per channel
• Stereo Operation Stereo Link, per channel pair; Two-position switch (Normal, Link)
• Maximum Input Level Mic: +14dBu; Line: +28dBu
• Input Impedance Mic: 2.4k ohms; Line (TRS): 33k ohms; Insert Return: 39k ohms
• A/D Freq. Response -0.1dB @ 20kHz (-0.4dB @ 20.0kHz, measured from Mic or Line in) -3dB @ 1.5Hz (-3dB @ 2.0Hz, measured from Mic or Line in)
• THD +N < 0.003%
• Crosstalk -90db
• Bit Error Rate (BER) 10(-12)
• Signal to Noise (unweighted) A/D: -105dB Reference = +14dBu (A/D clip point) Send jack: -113dB (Gain = minimum)
• EIN (Equivalent Input Noise) -128dBu (Rs = 150 ohms, 20kHz BW, Gain = +60dB)
• CMRR (Common Mode Rejection Ratio) 80dB @ 120Hz (Gain = +60dB)
• Low Cut Filter -3dB @ 85Hz, -18 dB per octave
• Phantom Power +48 volts, per channel, switch with LED
• Digital Outputs A-Net: 2 (Main and Aux); A-Net Expansion: 1
• A-Net Pro16 A-Net Expansion combines two A-Net streams (32 channels of audio) onto one Cat-5e cable uses unshielded Cat-5e UTP (or better) cable
• Latency <0.880 msec (measured from analog input to analog output)
• Power Supply Internal, universal switching type; IEC jack
• Voltage 100-240VAC, 50-60Hz, 60W; Fuse: 250VAC, F4AL
• Dimension 19 x 9.25 in. (482.6 x 234.95mm); 3U high
• Weight 12 pounds (5.44 kilo)
• Options AN-16SB System Bridge; used to combine up to four A-Net streams for transmission over one Cat-5e cable