The AV-P2 Output Module provides up to two channels of analog outputs from a Pro16 A-Net digital audio stream. The analog output level for each channel is set with front-panel DIP switches.

AV-P2 modules can be connected in any combination of serial or parallel connections, using Pro16 A-Net Distributors. There is no limit to the number of devices that can be daisy chained, or to the number of parallel splits in a single system.

Each AV-P2 receives a 16-channel A-Net stream originating at a Pro16 input module, console interface card, or Pro64™ audio network (via the ASI A-Net Systems Interface module).

A front-panel rotary switch allows the output to be set to any one of those 16 channels. If the selected channel is part of a stereo pair (set at the input module), the left and right channels are automatically routed to the left and right outputs on the AV-P2. If the selected channel is not part of a stereo pair, the channel's audio is routed to both the left and right outputs.

Audio is distributed to the AV-P2 over standard Cat-5e cables, using Aviom's A-Net digital audio protocol. A-Net supports plug-and-play installation, real-time distribution with sub-millisecond latency, and long cable runs up to 500ft/150m. Power can be supplied to the AV-P2 with an external DC power supply or over the Cat-5e cable (with an A-Net Distributor). Additionally, Pro16 A-Net audio streams can be transmitted over single- or multi-mode fiber optics using certain standard third-party media converters.

The AV-P2 has reversible mounting flanges. Two AV-P2 modules can be mounted side by side on a standard 1U rack tray. The AV-P2 is compatible with all Pro16 Series products.

Aviom AV-P2

• Provides 1- or 2-channel analog output from a Pro16 A-Net stream
• Independently selectable output levels for left and right channels
• 48kHz, 24-bit D/A converters
• Optional power over Cat-5e using a Pro16 A-Net Distributor
• Simple plug-and-play installation
• Secure set- and-forget channel configuration
• Reversible mounting flanges

AV-P2

• Audio Outputs: 2, impedance balanced line-level; 5.0 mm Euroblock connectors, female, panel- mount ; 2 male Euroblock connectors supplied in box; Screw terminals: Audio +; Audio -; Ground
• Channel Selection: 16-position rotary switch
• D/A Conversion: 48kHz, 24-bit
• Output Levels: Variable: +4dBu to -31dBu in 1.5dB increments 6-position DIP switch, per channel
• Indicators : LEDs;; red: Power, green: A-Net Active, yellow: Stereo Pair
• Output Impedance: 100 ohms
• Signal to Noise: (unweighted) 93dB typical, A/D to D/A Measured from AN-16/i Input Module to AV-P2 Freq. Response: 4Hz-22kHz +0.2dB/-3dB
• THD +N: -93dB at -10dBFS
• Crosstalk: -85dB at 1kHz
• Bit Error Rate (BER): 10-¹²
• Digital Connections: A-Net In: 1; A-Net Out: 1; RJ45 connectors
• Pro16 A-Net®: Uses unshielded Cat-5e UTP (or better) cable
• Latency: <0.880 msec (measured from analog input to analog output)
• Power Supply: External, DC, universal switching type
• Input Voltage 100-240 volts, 50/60Hz, 30VA
• Output Voltage 18-24 VDC, 0.5 amp
• Plug Size 2 mm, locking, center pin hot
• Dimensions: 7.45" (189.2 mm) wide x 7" (177.8 mm) deep; 1U high 1.75" (44.45mm)
• Weight: 3.4 lbs (1.54 kg)